Spinning Dorset Horn Roving

It’s been awhile since I’ve finished a Shave ‘Em to Save ‘Em project – the last few months have been a bit of a whirlwind and haven’t left me much time for spinning. I’ve been working on this lovely natural gray-brown Dorset Horn from Covered Bridge Fiber for several months, and finally finished it off last week.

According to The Fleece and Fiber Sourcebook, Dorset Horn sheep originated in Dorset, a county in southwestern England, and have fleece with a regular, fine crimp with plenty of elascticity. The micron count is typically between 26 and 33, which puts them in the medium wool range. The Livestock Breed Conservancy lists the breed as Threatened; you can find a fiber profile on the Conservancy’s website. They are usually white but can occasionally be near-black in color. Lucky me to have found this gorgeous shade of fiber!

After spindle spinning just under an ounce of the fiber for my blanket project, I set up to spin the fiber on my wheel. While Dorset Horn not a Down breed, this fiber did have a bit of that spongy feel that’s characteristic of the Down breeds, so I assumed this fiber would be amenable to spinning londraw. I had visions of a hat or mittens in a lofty thicker yarn.

But I had trouble initially spinning it as fine as I wanted with longdraw, perhaps because the staple length is a bit longer than other breeds I’ve spun longdraw, such as Clun Forest. I don’t often take the time to actually measure staple length of fibers I’m spinning; I just pull out a staple and eyeball it. But this time I got curious and actually measured – the staple length was around 3 inches.

I found myself wanting to spin the fiber semi-woolen with a short forward draw. It seemed to want to spin relatively fine that way, so I settled on a fingering weight 2-ply. I figured it could be used to knit a sturdy pair of mittens or even as a weaving yarn.

I started spinning the singles at a 12:1 ratio with about a 2-inch draft. But I found I wasn’t enjoying this project over the long haul, and about 3/4 of the way through I gave long-draw another go. This time I was able to spin fine enough to match the singles I already had, so I went with it and finished the bobbin that way. Needless to say, this spin isn’t going to win any consistency awards, but I’m satisfied with the end result. Oddly enough, the skein spun completely with a worsted draft seems to have fluffed up more after finishing than the skein where I switched to long-draw halfway through. Go figure.

The resulting yarn is pleasantly soft, if not next-to-skin soft. I could see buying a sweater’s worth of this fiber and spinning it for a fingering-weight sweater.


Subscribe to my Monthly Musings newsletter and receive a free cowl pattern! When you subscribe you will receive a free download of my Diagonal Rib Cowl. You’ll also be the first to hear about new releases and other fiber-related news.

Processing…
Success! You're on the list.

Did you find this post helpful?

Buy Me a Coffee at ko-fi.com


Sampling CVM for Cables – Woolen vs. Semi-Woolen

I’ve been sampling some CVM fiber (from Heelside Farms) for my next Shave ‘Em to Save ‘Em project. I’ve been thinking I might want to knit a cabled sweater with this fiber, and I was wondering if my drafting method would make a difference in the cable definition. I would expect that, since worsted-spun yarns are often touted for their cable definition, getting closer to that with a semi-woolen yarn would give me cables that ‘pop’ more while retaining the softer, rustic look of a woolen-spun yarn. But a woolen spun yarn would likely be faster to spin, so I wanted to make sure the extra time for a worsted draft was really worth it. So I did a little experiment.

I’m starting from roving, so my options are to create a semi-woolen yarn using a short forward draft, or go for a fully woolen-spun yarn using longdraw. I pulled off a small amount to sample each way, and attempted to spin yarns with approximately the same diameter and ply twist. Both yarns came out to around a DK weight, and with similar ply twist. The woolen-spun sample came out a bit more uneven, and has a bit of a thick and think quality to it. I also had some areas that were underspun in the singles, so breakage was a problem. I would want to spin a more careful sample before I decided to use this for a sweater, but for my comparison purposes I assumed it would suffice. Unsurprisingly the woolen-spun sample had slightly less twist overall in the singles.

Yarn butterflies of CVM - woolen-spun and semi-woolen.
Left: woolen-spun CVM (spun longdraw); Right: semi-woolen CVM (spun with short forward draft)

I cast on and knit two swatches on US #7 (4.5mm) needles, using a simple 3×3 cable as a test. The woolen-spun swatch came out slightly bigger for the same number of stitches as I would expect – it measured about 3 3/4″ over 20 stitches vs about 3 1/2″ for the semi-woolen swatch. And the cable does appear a bit flatter and less three-dimensional, which I suspected might happen. The semi-woolen swatch also has better stitch definition overall. What surprised me a bit, though, was in that the swatch spun with a short forward draft the stitches appear a bit puffier and seem to fill in the space better. That could be because of my inconsistency in spinning the woolen swatch, though. The other thing that surprised me was the difference in weight of the swatches. I know woolen-spun yarns tend to be lighter, but I was surprised that the two swatches spun from roving were so different. The semi-woolen swatch weighed 4.5 g versus 4.3 g for the woolen-spun – not a huge difference in a swatch of this size. But it made a noticeable difference to the feel of the swatch in my hand. It might be worth sacrificing a bit of cable definition to get a lighter, cozier feeling sweater. I like the look of both cables, and even though the draft did make a difference I’m not sure it was enough to prefer one draft over the other on that basis.

Two handknit cable swatches comparing woolen-spun vs. semi-woolen CVM.
My two cable swatches: woolen spun using longdraw (L) and semi-woolen (R) using short forward draft.

I haven’t decided yet if I will knit a sweater with this fiber – I would need to purchase more of it – or, if I do, which draft I will use. I also want to test how these swatches will stand up to wear – maybe a topic for another post. But I do have an idea of how my choices will affect the final yarn and what I might use it for.